Cacher is the code snippet organizer for pro developers

;
;
;- – - – SUMMARY – - – -
;
;first layer temperature (right) = [first_layer_temperature_0]C
;first layer temperature (left) = [first_layer_temperature_1]C
;temperature (right) = [temperature_0]C
;temperature (left) = [temperature_1]C
;first layer bed temperature = [first_layer_bed_temperature]C
;bed temperature = [bed_temperature]C
;
;first layer height = [first_layer_height]mm
;layer height = [layer_height]mm
;z_offset = [z_offset]mm
;perimeters = [perimeters]
;fill density = [fill_density]
;infill every n layers = [infill_every_layers]
;skirts = [skirts]
;brim width = [brim_width]mm
;raft layers = [raft_layers]
;support material = [support_material]
;support material threshold = [support_material_threshold] degrees
;support material enforced for first n layers = [support_material_enforce_layers]
;support material extruder = [support_material_extruder]
;
;first layer speed = [first_layer_speed]
;perimeter speed = [perimeter_speed]mm/s
;small perimeter speed = [small_perimeter_speed]
;external perimeter speed = [external_perimeter_speed]
;infill speed = [infill_speed]mm/s
;solid infill speed = [solid_infill_speed]
;top solid infill speed = [top_solid_infill_speed]
;support material speed = [support_material_speed]mm/s
;gap fill speed = [gap_fill_speed]mm/s
;travel speed = [travel_speed]mm/s
;bridge speed = [bridge_speed]mm/s
;bridge flow ratio = [bridge_flow_ratio]
;slowdown if layer time is less than = [slowdown_below_layer_time]secs
;minimum print speed = [min_print_speed]mm/s
;
;bottom solid layers = [bottom_solid_layers]
;top solid layers = [top_solid_layers]
;
;
;- – - – EXTRUSION – - – -
;
;filament diameter (right) = [filament_diameter_0]mm
;nozzle diameter (right) = [nozzle_diameter_0]mm
;extrusion multiplier (right) = [extrusion_multiplier_0]
;filament diameter (left) = [filament_diameter_1]mm
;nozzle diameter (left) = [nozzle_diameter_1]mm
;extrusion multiplier (left) = [extrusion_multiplier_1]
;bridge flow ratio = [bridge_flow_ratio]
;extrusion axis = [extrusion_axis]
;extrusion width = [extrusion_width]mm
;first layer extrusion width = [first_layer_extrusion_width]mm
;perimeter extrusion width = [perimeter_extrusion_width]mm
;infill extrusion width = [infill_extrusion_width]mm
;solid infill extrusion width = [solid_infill_extrusion_width]mm
;top infill extrusion width = [top_infill_extrusion_width]mm
;support material extrusion width = [support_material_extrusion_width]mm
;
;
;- – - – SUPPORT – - – -
;
;raft layers = [raft_layers]
;brim width = [brim_width]mm
;support material = [support_material]
;support material threshold = [support_material_threshold] degrees
;support material enforced for first n layers = [support_material_enforce_layers]
;support material extruder = [support_material_extruder]
;support material extrusion width = [support_material_extrusion_width]mm
;support material interface layers = [support_material_interface_layers]
;support material interface spacing = [support_material_interface_spacing]mm
;support material pattern = [support_material_pattern]
;support material angle = [support_material_angle] degrees
;support material spacing = [support_material_spacing]mm
;support material speed = [support_material_speed]mm/s
;
;
;- – - – EVERYTHING ELSE – - – -
;
;complete objects = [complete_objects]
;cooling enabled = [cooling]
;default acceleration = [default_acceleration]mm/s/s
;disable fan for first layers = [disable_fan_first_layers]
;duplicate = [duplicate]
;duplicate distance = [duplicate_distance]mm
;duplicate grid = [duplicate_grid]
;external perimeters first = [external_perimeters_first]
;extra perimeters = [extra_perimeters]
;extruder clearance height = [extruder_clearance_height]mm
;extruder clearance radius = [extruder_clearance_radius]mm
;extruder offset = [extruder_offset]mm
;fan always on = [fan_always_on]
;fan below layer time = [fan_below_layer_time]secs
;fill angle = [fill_angle] degrees
;fill pattern = [fill_pattern]
;gcode arcs = [gcode_arcs]
;gcode comments = [gcode_comments]
;gcode flavor = [gcode_flavor]
;infill acceleration = [infill_acceleration]mm/s/s
;infill extruder = [infill_extruder]
;infill first = [infill_first]
;infill only where needed = [infill_only_where_needed]
;minimum skirt length = [min_skirt_length]mm
;only retract when crossing perimeters = [only_retract_when_crossing_perimeters]
;perimeter acceleration = [perimeter_acceleration]mm/s/s
;perimeter extruder = [perimeter_extruder]
;randomize start = [randomize_start]
;resolution = [resolution]mm
;retract before travel (right) = [retract_before_travel_0]
;retract on layer change (right) = [retract_layer_change_0]
;retract length (right) = [retract_length_0]mm
;retract length on tool change (right) = [retract_length_toolchange_0]mm
;retract lift (right) = [retract_lift_0]
;retract extra distance on restart (right) = [retract_restart_extra_0]mm
;retract extra on tool change (right) = [retract_restart_extra_toolchange_0]mm
;retract speed (right) = [retract_speed_0]mm/s
;retract before travel (left) = [retract_before_travel_1]
;retract on layer change (left) = [retract_layer_change_1]
;retract length (left) = [retract_length_1]mm
;retract length on tool change (left) = [retract_length_toolchange_1]mm
;retract lift (left) = [retract_lift_1]
;retract extra distance on restart (left) = [retract_restart_extra_1]mm
;retract extra on tool change (left) = [retract_restart_extra_toolchange_1]mm
;retract speed (left) = [retract_speed_1]mm/s
;rotate = [rotate] degrees
;scale = [scale]
;skirt distance = [skirt_distance]mm
;skirt height = [skirt_height]mm
;solid fill pattern = [solid_fill_pattern]
;solid infill below area = [solid_infill_below_area]mm (sq)
;solid infill every n layers = [solid_infill_every_layers]
;
;
;- – - – - – - – - – - – - – - – - – - – - – - – -
;
;
T0; set primary extruder
M73 P0; enable show build progress
M109 S[first_layer_bed_temperature] T0 ; heat bed up to first layer temperature
M104 S[first_layer_temperature_0] T0 ; set 1st nozzle heater to first layer temperature
M104 S[first_layer_temperature_1] T1 ; set 2nd nozzle heater to first layer temperature
M103; disable RPM
G21; set units to mm
G162 X Y F9000; home XY axes maximum
G161 Z F6000; home Z axis minimum
G92 Z0; set Z to 0
M132 X Y Z A B; Recall stored home offsets
G90; set positioning to absolute
G1 Z30; move Z to waiting height
G1 X-95 Y-73 Z30 F12000.0; move to waiting position (front left corner of print bed)
G130 X0 Y0 A0 B0; set stepper motor vref to lower value while heating
M6 T0; wait for bed and extruder 1 to heat up
M6 T1; wait for extruder 2 to heat up
T0; change to primary extruder
G130 X127 Y127 A127 B127; set stepper motor vref to defaults
M108 T0 R3; set extruder speed
G92 E0; set E to 0
M320; acceleration enabled for all commands that follow
G1 Z[first_layer_height] F6000.000; move to first layer height
G1 X100 Y-73 F14000.000; move to front right corner of bed
G1 X-90 Y-73 E24 F2000.000; extrude a line of filament across the front edge of the bed using the 1st extuder
G92 E[retract_length]; set E to retraction length defined in printer settings
G4 P2000; wait for ooze to slow
G1 E0 F5400; excute reverse extrusion to retract by length defined in printer settings
G1 Z0 F6000.000; lower nozzle height to 0
G1 X-95; wipe purged noodle on edge of bed
G92 E0; set E to 0 for 1st extruder
T1; switch to 2nd extruder
G1 Z[first_layer_height] F6000.000; set nozzle to first layer height
G1 X100 Y-71 F14000.000; move to front right corner of print bed
G1 X-90 Y-71 E24 F2000.000; extrude a line of filament across the front edge of the bed using the 2nd extuder
G4 P2000; wait for ooze to slow
G1 Z0 F6000.000; lower nozzle height to 0
G1 X-95; wipe purged noodle on edge of bed
G1 Z[first_layer_height] F6000.000; set nozzle to first layer height
G1 F14000; ensure fast travel to first print move
G92 E0; set E to 0 for 2nd extruder
T0; switch to 1st extruder
M73 P0; reset build progress to 0

M73 P100 ; end build progress
G162 X Y F2500; home X and Y axes
M109 S0 T0; set bed temperature to 0
M104 S0 T0; set 1st extruder temperature to 0
M104 S0 T1; set 2nd extruder temperature to 0
M18; disable all stepper motors
M70 P5; Display "We <3 Making Things!" message
M72 P1; Play Ta-Da song