kylemanna
3/20/2017 - 9:27 PM
zc702-zynq7-system.dts
/dts-v1/;
/ {
#address-cells = <0x1>;
#size-cells = <0x1>;
compatible = "xlnx,zynq-zc702", "xlnx,zynq-7000";
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
};
aliases {
ethernet0 = "/amba/ethernet@e000b000";
serial0 = "/amba/serial@e0001000";
spi0 = "/amba/spi@e000d000";
};
memory {
device_type = "memory";
reg = <0x0 0x40000000>;
};
cpus {
#address-cells = <0x1>;
#size-cells = <0x0>;
cpu@0 {
compatible = "arm,cortex-a9";
device_type = "cpu";
reg = <0x0>;
clocks = <0x1 0x3>;
clock-latency = <0x3e8>;
cpu0-supply = <0x2>;
operating-points = <0xa2c2a 0xf4240 0x51615 0xf4240>;
};
cpu@1 {
compatible = "arm,cortex-a9";
device_type = "cpu";
reg = <0x1>;
clocks = <0x1 0x3>;
};
};
fpga-full {
compatible = "fpga-region";
fpga-mgr = <0x3>;
#address-cells = <0x1>;
#size-cells = <0x1>;
ranges;
};
pmu {
compatible = "arm,cortex-a9-pmu";
interrupts = <0x0 0x5 0x4 0x0 0x6 0x4>;
interrupt-parent = <0x4>;
reg = <0xf8891000 0x1000 0xf8893000 0x1000>;
};
fixedregulator@0 {
compatible = "regulator-fixed";
regulator-name = "VCCPINT";
regulator-min-microvolt = <0xf4240>;
regulator-max-microvolt = <0xf4240>;
regulator-boot-on;
regulator-always-on;
linux,phandle = <0x2>;
phandle = <0x2>;
};
amba {
compatible = "simple-bus";
#address-cells = <0x1>;
#size-cells = <0x1>;
interrupt-parent = <0x4>;
ranges;
adc@f8007100 {
compatible = "xlnx,zynq-xadc-1.00.a";
reg = <0xf8007100 0x20>;
interrupts = <0x0 0x7 0x4>;
interrupt-parent = <0x4>;
clocks = <0x1 0xc>;
};
can@e0008000 {
compatible = "xlnx,zynq-can-1.0";
status = "disabled";
clocks = <0x1 0x13 0x1 0x24>;
clock-names = "can_clk", "pclk";
reg = <0xe0008000 0x1000>;
interrupts = <0x0 0x1c 0x4>;
interrupt-parent = <0x4>;
tx-fifo-depth = <0x40>;
rx-fifo-depth = <0x40>;
pinctrl-names = "default";
pinctrl-0 = <0x5>;
};
can@e0009000 {
compatible = "xlnx,zynq-can-1.0";
status = "disabled";
clocks = <0x1 0x14 0x1 0x25>;
clock-names = "can_clk", "pclk";
reg = <0xe0009000 0x1000>;
interrupts = <0x0 0x33 0x4>;
interrupt-parent = <0x4>;
tx-fifo-depth = <0x40>;
rx-fifo-depth = <0x40>;
};
gpio@e000a000 {
compatible = "xlnx,zynq-gpio-1.0";
#gpio-cells = <0x2>;
clocks = <0x1 0x2a>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <0x2>;
interrupt-parent = <0x4>;
interrupts = <0x0 0x14 0x4>;
reg = <0xe000a000 0x1000>;
pinctrl-names = "default";
pinctrl-0 = <0x6>;
emio-gpio-width = <0x40>;
gpio-mask-high = <0x0>;
gpio-mask-low = <0x5600>;
linux,phandle = <0x9>;
phandle = <0x9>;
};
i2c@e0004000 {
compatible = "cdns,i2c-r1p10";
status = "disabled";
clocks = <0x1 0x26>;
interrupt-parent = <0x4>;
interrupts = <0x0 0x19 0x4>;
reg = <0xe0004000 0x1000>;
#address-cells = <0x1>;
#size-cells = <0x0>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <0x7>;
pinctrl-1 = <0x8>;
scl-gpios = <0x9 0x32 0x0>;
sda-gpios = <0x9 0x33 0x0>;
i2cswitch@74 {
compatible = "nxp,pca9548";
#address-cells = <0x1>;
#size-cells = <0x0>;
reg = <0x74>;
i2c@0 {
#address-cells = <0x1>;
#size-cells = <0x0>;
reg = <0x0>;
clock-generator@5d {
#clock-cells = <0x0>;
compatible = "silabs,si570";
temperature-stability = <0x32>;
reg = <0x5d>;
factory-fout = <0x9502f90>;
clock-frequency = <0x8d9ee20>;
};
};
i2c@1 {
#address-cells = <0x1>;
#size-cells = <0x0>;
reg = <0x1>;
hdmi-tx@39 {
compatible = "adi,adv7511";
reg = <0x39>;
adi,input-depth = <0x8>;
adi,input-colorspace = "yuv422";
adi,input-clock = "1x";
adi,input-style = <0x3>;
adi,input-justification = "right";
};
};
i2c@2 {
#address-cells = <0x1>;
#size-cells = <0x0>;
reg = <0x2>;
eeprom@54 {
compatible = "at,24c08";
reg = <0x54>;
};
};
i2c@3 {
#address-cells = <0x1>;
#size-cells = <0x0>;
reg = <0x3>;
gpio@21 {
compatible = "ti,tca6416";
reg = <0x21>;
gpio-controller;
#gpio-cells = <0x2>;
};
};
i2c@4 {
#address-cells = <0x1>;
#size-cells = <0x0>;
reg = <0x4>;
rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
};
i2c@7 {
#address-cells = <0x1>;
#size-cells = <0x0>;
reg = <0x7>;
hwmon@52 {
compatible = "ti,ucd9248";
reg = <0x34>;
};
hwmon@53 {
compatible = "ti,ucd9248";
reg = <0x35>;
};
hwmon@54 {
compatible = "ti,ucd9248";
reg = <0x36>;
};
};
};
};
i2c@e0005000 {
compatible = "cdns,i2c-r1p10";
status = "disabled";
clocks = <0x1 0x27>;
interrupt-parent = <0x4>;
interrupts = <0x0 0x30 0x4>;
reg = <0xe0005000 0x1000>;
#address-cells = <0x1>;
#size-cells = <0x0>;
};
interrupt-controller@f8f01000 {
compatible = "arm,cortex-a9-gic";
#interrupt-cells = <0x3>;
interrupt-controller;
reg = <0xf8f01000 0x1000 0xf8f00100 0x100>;
num_cpus = <0x2>;
num_interrupts = <0x60>;
linux,phandle = <0x4>;
phandle = <0x4>;
};
cache-controller@f8f02000 {
compatible = "arm,pl310-cache";
reg = <0xf8f02000 0x1000>;
interrupts = <0x0 0x2 0x4>;
arm,data-latency = <0x3 0x2 0x2>;
arm,tag-latency = <0x2 0x2 0x2>;
cache-unified;
cache-level = <0x2>;
};
memory-controller@f8006000 {
compatible = "xlnx,zynq-ddrc-a05";
reg = <0xf8006000 0x1000>;
};
ocmc@f800c000 {
compatible = "xlnx,zynq-ocmc-1.0";
interrupt-parent = <0x4>;
interrupts = <0x0 0x3 0x4>;
reg = <0xf800c000 0x1000>;
};
serial@e0000000 {
compatible = "xlnx,xuartps", "cdns,uart-r1p8";
status = "disabled";
clocks = <0x1 0x17 0x1 0x28>;
clock-names = "uart_clk", "pclk";
reg = <0xe0000000 0x1000>;
interrupts = <0x0 0x1b 0x4>;
};
serial@e0001000 {
compatible = "xlnx,xuartps", "cdns,uart-r1p8";
status = "okay";
clocks = <0x1 0x18 0x1 0x29>;
clock-names = "uart_clk", "pclk";
reg = <0xe0001000 0x1000>;
interrupts = <0x0 0x32 0x4>;
u-boot,dm-pre-reloc;
pinctrl-names = "default";
pinctrl-0 = <0xa>;
device_type = "serial";
port-number = <0x0>;
};
spi@e0006000 {
compatible = "xlnx,zynq-spi-r1p6";
reg = <0xe0006000 0x1000>;
status = "disabled";
interrupt-parent = <0x4>;
interrupts = <0x0 0x1a 0x4>;
clocks = <0x1 0x19 0x1 0x22>;
clock-names = "ref_clk", "pclk";
#address-cells = <0x1>;
#size-cells = <0x0>;
};
spi@e0007000 {
compatible = "xlnx,zynq-spi-r1p6";
reg = <0xe0007000 0x1000>;
status = "disabled";
interrupt-parent = <0x4>;
interrupts = <0x0 0x31 0x4>;
clocks = <0x1 0x1a 0x1 0x23>;
clock-names = "ref_clk", "pclk";
#address-cells = <0x1>;
#size-cells = <0x0>;
};
spi@e000d000 {
clock-names = "ref_clk", "pclk";
clocks = <0x1 0xa 0x1 0x2b>;
compatible = "xlnx,zynq-qspi-1.0";
status = "okay";
interrupt-parent = <0x4>;
interrupts = <0x0 0x13 0x4>;
reg = <0xe000d000 0x1000>;
#address-cells = <0x1>;
#size-cells = <0x0>;
is-dual = <0x0>;
num-cs = <0x1>;
};
memory-controller@e000e000 {
#address-cells = <0x1>;
#size-cells = <0x1>;
status = "disabled";
clock-names = "memclk", "aclk";
clocks = <0x1 0xb 0x1 0x2c>;
compatible = "arm,pl353-smc-r2p1";
interrupt-parent = <0x4>;
interrupts = <0x0 0x12 0x4>;
ranges;
reg = <0xe000e000 0x1000>;
flash@e1000000 {
status = "disabled";
compatible = "arm,pl353-nand-r2p1";
reg = <0xe1000000 0x1000000>;
#address-cells = <0x1>;
#size-cells = <0x1>;
};
flash@e2000000 {
status = "disabled";
compatible = "cfi-flash";
reg = <0xe2000000 0x2000000>;
#address-cells = <0x1>;
#size-cells = <0x1>;
};
};
ethernet@e000b000 {
compatible = "cdns,zynq-gem", "cdns,gem";
reg = <0xe000b000 0x1000>;
status = "okay";
interrupts = <0x0 0x16 0x4>;
clocks = <0x1 0x1e 0x1 0x1e 0x1 0xd>;
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <0x1>;
#size-cells = <0x0>;
phy-handle = <0xb>;
pinctrl-names = "default";
pinctrl-0 = <0xc>;
phy-reset-gpio = <0x9 0xb 0x0>;
phy-reset-active-low;
phy-mode = "rgmii-id";
xlnx,ptp-enet-clock = <0x69f6bcb>;
ethernet-phy@7 {
reg = <0x7>;
device_type = "ethernet-phy";
linux,phandle = <0xb>;
phandle = <0xb>;
};
};
ethernet@e000c000 {
compatible = "cdns,zynq-gem", "cdns,gem";
reg = <0xe000c000 0x1000>;
status = "disabled";
interrupts = <0x0 0x2d 0x4>;
clocks = <0x1 0x1f 0x1 0x1f 0x1 0xe>;
clock-names = "pclk", "hclk", "tx_clk";
#address-cells = <0x1>;
#size-cells = <0x0>;
};
sdhci@e0100000 {
compatible = "arasan,sdhci-8.9a";
status = "okay";
clock-names = "clk_xin", "clk_ahb";
clocks = <0x1 0x15 0x1 0x20>;
interrupt-parent = <0x4>;
interrupts = <0x0 0x18 0x4>;
reg = <0xe0100000 0x1000>;
broken-adma2;
u-boot,dm-pre-reloc;
pinctrl-names = "default";
pinctrl-0 = <0xd>;
xlnx,has-cd = <0x1>;
xlnx,has-power = <0x0>;
xlnx,has-wp = <0x0>;
};
sdhci@e0101000 {
compatible = "arasan,sdhci-8.9a";
status = "okay";
clock-names = "clk_xin", "clk_ahb";
clocks = <0x1 0x16 0x1 0x21>;
interrupt-parent = <0x4>;
interrupts = <0x0 0x2f 0x4>;
reg = <0xe0101000 0x1000>;
broken-adma2;
xlnx,has-cd = <0x0>;
xlnx,has-power = <0x0>;
xlnx,has-wp = <0x0>;
};
slcr@f8000000 {
#address-cells = <0x1>;
#size-cells = <0x1>;
compatible = "xlnx,zynq-slcr", "syscon", "simple-mfd";
reg = <0xf8000000 0x1000>;
ranges;
linux,phandle = <0xe>;
phandle = <0xe>;
clkc@100 {
#clock-cells = <0x1>;
compatible = "xlnx,ps7-clkc";
fclk-enable = <0x1>;
clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x", "cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x", "dci", "lqspi", "smc", "pcap", "gem0", "gem1", "fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1", "sdio0", "sdio1", "uart0", "uart1", "spi0", "spi1", "dma", "usb0_aper", "usb1_aper", "gem0_aper", "gem1_aper", "sdio0_aper", "sdio1_aper", "spi0_aper", "spi1_aper", "can0_aper", "can1_aper", "i2c0_aper", "i2c1_aper", "uart0_aper", "uart1_aper", "gpio_aper", "lqspi_aper", "smc_aper", "swdt", "dbg_trc", "dbg_apb";
reg = <0x100 0x100>;
ps-clk-frequency = <0x1fca055>;
linux,phandle = <0x1>;
phandle = <0x1>;
};
rstc@200 {
compatible = "xlnx,zynq-reset";
reg = <0x200 0x48>;
#reset-cells = <0x1>;
syscon = <0xe>;
};
pinctrl@700 {
compatible = "xlnx,pinctrl-zynq";
reg = <0x700 0x200>;
syscon = <0xe>;
can0-default {
linux,phandle = <0x5>;
phandle = <0x5>;
mux {
function = "can0";
groups = "can0_9_grp";
};
conf {
groups = "can0_9_grp";
slew-rate = <0x0>;
io-standard = <0x1>;
};
conf-rx {
pins = "MIO46";
bias-high-impedance;
};
conf-tx {
pins = "MIO47";
bias-disable;
};
};
gem0-default {
linux,phandle = <0xc>;
phandle = <0xc>;
mux {
function = "ethernet0";
groups = "ethernet0_0_grp";
};
conf {
groups = "ethernet0_0_grp";
slew-rate = <0x0>;
io-standard = <0x4>;
};
conf-rx {
pins = "MIO22", "MIO23", "MIO24", "MIO25", "MIO26", "MIO27";
bias-high-impedance;
low-power-disable;
};
conf-tx {
pins = "MIO16", "MIO17", "MIO18", "MIO19", "MIO20", "MIO21";
bias-disable;
low-power-enable;
};
mux-mdio {
function = "mdio0";
groups = "mdio0_0_grp";
};
conf-mdio {
groups = "mdio0_0_grp";
slew-rate = <0x0>;
io-standard = <0x1>;
bias-disable;
};
};
gpio0-default {
linux,phandle = <0x6>;
phandle = <0x6>;
mux {
function = "gpio0";
groups = "gpio0_7_grp", "gpio0_8_grp", "gpio0_9_grp", "gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp", "gpio0_13_grp", "gpio0_14_grp";
};
conf {
groups = "gpio0_7_grp", "gpio0_8_grp", "gpio0_9_grp", "gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp", "gpio0_13_grp", "gpio0_14_grp";
slew-rate = <0x0>;
io-standard = <0x1>;
};
conf-pull-up {
pins = "MIO9", "MIO10", "MIO11", "MIO12", "MIO13", "MIO14";
bias-pull-up;
};
conf-pull-none {
pins = "MIO7", "MIO8";
bias-disable;
};
};
i2c0-default {
linux,phandle = <0x7>;
phandle = <0x7>;
mux {
groups = "i2c0_10_grp";
function = "i2c0";
};
conf {
groups = "i2c0_10_grp";
bias-pull-up;
slew-rate = <0x0>;
io-standard = <0x1>;
};
};
i2c0-gpio {
linux,phandle = <0x8>;
phandle = <0x8>;
mux {
groups = "gpio0_50_grp", "gpio0_51_grp";
function = "gpio0";
};
conf {
groups = "gpio0_50_grp", "gpio0_51_grp";
slew-rate = <0x0>;
io-standard = <0x1>;
};
};
sdhci0-default {
linux,phandle = <0xd>;
phandle = <0xd>;
mux {
groups = "sdio0_2_grp";
function = "sdio0";
};
conf {
groups = "sdio0_2_grp";
slew-rate = <0x0>;
io-standard = <0x1>;
bias-disable;
};
mux-cd {
groups = "gpio0_0_grp";
function = "sdio0_cd";
};
conf-cd {
groups = "gpio0_0_grp";
bias-high-impedance;
bias-pull-up;
slew-rate = <0x0>;
io-standard = <0x1>;
};
mux-wp {
groups = "gpio0_15_grp";
function = "sdio0_wp";
};
conf-wp {
groups = "gpio0_15_grp";
bias-high-impedance;
bias-pull-up;
slew-rate = <0x0>;
io-standard = <0x1>;
};
};
uart1-default {
linux,phandle = <0xa>;
phandle = <0xa>;
mux {
groups = "uart1_10_grp";
function = "uart1";
};
conf {
groups = "uart1_10_grp";
slew-rate = <0x0>;
io-standard = <0x1>;
};
conf-rx {
pins = "MIO49";
bias-high-impedance;
};
conf-tx {
pins = "MIO48";
bias-disable;
};
};
usb0-default {
linux,phandle = <0x10>;
phandle = <0x10>;
mux {
groups = "usb0_0_grp";
function = "usb0";
};
conf {
groups = "usb0_0_grp";
slew-rate = <0x0>;
io-standard = <0x1>;
};
conf-rx {
pins = "MIO29", "MIO31", "MIO36";
bias-high-impedance;
};
conf-tx {
pins = "MIO28", "MIO30", "MIO32", "MIO33", "MIO34", "MIO35", "MIO37", "MIO38", "MIO39";
bias-disable;
};
};
};
};
dmac@f8003000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0xf8003000 0x1000>;
interrupt-parent = <0x4>;
interrupt-names = "abort", "dma0", "dma1", "dma2", "dma3", "dma4", "dma5", "dma6", "dma7";
interrupts = <0x0 0xd 0x4 0x0 0xe 0x4 0x0 0xf 0x4 0x0 0x10 0x4 0x0 0x11 0x4 0x0 0x28 0x4 0x0 0x29 0x4 0x0 0x2a 0x4 0x0 0x2b 0x4>;
#dma-cells = <0x1>;
#dma-channels = <0x8>;
#dma-requests = <0x4>;
clocks = <0x1 0x1b>;
clock-names = "apb_pclk";
};
devcfg@f8007000 {
compatible = "xlnx,zynq-devcfg-1.0";
interrupt-parent = <0x4>;
interrupts = <0x0 0x8 0x4>;
reg = <0xf8007000 0x100>;
clocks = <0x1 0xc 0x1 0xf 0x1 0x10 0x1 0x11 0x1 0x12>;
clock-names = "ref_clk", "fclk0", "fclk1", "fclk2", "fclk3";
syscon = <0xe>;
linux,phandle = <0x3>;
phandle = <0x3>;
};
efuse@f800d000 {
compatible = "xlnx,zynq-efuse";
reg = <0xf800d000 0x20>;
};
timer@f8f00200 {
compatible = "arm,cortex-a9-global-timer";
reg = <0xf8f00200 0x20>;
interrupts = <0x1 0xb 0x301>;
interrupt-parent = <0x4>;
clocks = <0x1 0x4>;
};
timer@f8001000 {
interrupt-parent = <0x4>;
interrupts = <0x0 0xa 0x4 0x0 0xb 0x4 0x0 0xc 0x4>;
compatible = "cdns,ttc";
clocks = <0x1 0x6>;
reg = <0xf8001000 0x1000>;
};
timer@f8002000 {
interrupt-parent = <0x4>;
interrupts = <0x0 0x25 0x4 0x0 0x26 0x4 0x0 0x27 0x4>;
compatible = "cdns,ttc";
clocks = <0x1 0x6>;
reg = <0xf8002000 0x1000>;
};
timer@f8f00600 {
interrupt-parent = <0x4>;
interrupts = <0x1 0xd 0x301>;
compatible = "arm,cortex-a9-twd-timer";
reg = <0xf8f00600 0x20>;
clocks = <0x1 0x4>;
};
usb@e0002000 {
compatible = "xlnx,zynq-usb-2.20a", "chipidea,usb2";
status = "okay";
clocks = <0x1 0x1c>;
interrupt-parent = <0x4>;
interrupts = <0x0 0x15 0x4>;
reg = <0xe0002000 0x1000>;
phy_type = "ulpi";
dr_mode = "host";
usb-phy = <0xf>;
pinctrl-names = "default";
pinctrl-0 = <0x10>;
usb-reset = <0x9 0x7 0x0>;
};
usb@e0003000 {
compatible = "xlnx,zynq-usb-2.20a", "chipidea,usb2";
status = "disabled";
clocks = <0x1 0x1d>;
interrupt-parent = <0x4>;
interrupts = <0x0 0x2c 0x4>;
reg = <0xe0003000 0x1000>;
phy_type = "ulpi";
};
watchdog@f8005000 {
clocks = <0x1 0x2d>;
compatible = "cdns,wdt-r1p2";
interrupt-parent = <0x4>;
interrupts = <0x0 0x9 0x1>;
reg = <0xf8005000 0x1000>;
timeout-sec = <0xa>;
};
sram@fffc0000 {
compatible = "mmio-sram";
reg = <0xfffc0000 0x10000>;
};
};
gpio-keys {
compatible = "gpio-keys";
#address-cells = <0x1>;
#size-cells = <0x0>;
autorepeat;
sw14 {
label = "sw14";
gpios = <0x9 0xc 0x0>;
linux,code = <0x6c>;
wakeup-source;
autorepeat;
};
sw13 {
label = "sw13";
gpios = <0x9 0xe 0x0>;
linux,code = <0x67>;
wakeup-source;
autorepeat;
};
};
leds {
compatible = "gpio-leds";
ds23 {
label = "ds23";
gpios = <0x9 0xa 0x0>;
linux,default-trigger = "heartbeat";
};
};
phy0@e0002000 {
compatible = "ulpi-phy";
#phy-cells = <0x0>;
reg = <0xe0002000 0x1000>;
view-port = <0x170>;
drv-vbus;
linux,phandle = <0xf>;
phandle = <0xf>;
};
amba_pl {
#address-cells = <0x1>;
#size-cells = <0x1>;
compatible = "simple-bus";
ranges;
gpio@41200000 {
#gpio-cells = <0x2>;
compatible = "xlnx,xps-gpio-1.00.a";
gpio-controller;
reg = <0x41200000 0x10000>;
xlnx,all-inputs = <0x0>;
xlnx,all-inputs-2 = <0x0>;
xlnx,all-outputs = <0x1>;
xlnx,all-outputs-2 = <0x0>;
xlnx,dout-default = <0x0>;
xlnx,dout-default-2 = <0x0>;
xlnx,gpio-width = <0x2>;
xlnx,gpio2-width = <0x20>;
xlnx,interrupt-present = <0x0>;
xlnx,is-dual = <0x0>;
xlnx,tri-default = <0xffffffff>;
xlnx,tri-default-2 = <0xffffffff>;
};
gpio@41210000 {
#gpio-cells = <0x2>;
compatible = "xlnx,xps-gpio-1.00.a";
gpio-controller;
reg = <0x41210000 0x10000>;
xlnx,all-inputs = <0x1>;
xlnx,all-inputs-2 = <0x0>;
xlnx,all-outputs = <0x0>;
xlnx,all-outputs-2 = <0x0>;
xlnx,dout-default = <0x0>;
xlnx,dout-default-2 = <0x0>;
xlnx,gpio-width = <0x1>;
xlnx,gpio2-width = <0x20>;
xlnx,interrupt-present = <0x0>;
xlnx,is-dual = <0x0>;
xlnx,tri-default = <0xffffffff>;
xlnx,tri-default-2 = <0xffffffff>;
};
};
};